Brand Name: | BLM-NC-1 |
Minimum Order Quantity: | Negotiation |
---|---|
Price: | Negotiation |
Packaging Details: | packed and labeled according to the regulations and customer's requests.Great care is taken to avoid any damage which might otherwise be caused during storage or transportation. |
Delivery Time: | 25-30 days subject to the clients' requirement and quantity |
Payment Terms: | Western Union, L/C, T/T |
Supply Ability: | 300 Ton/Tons per Month |
Place Of Origin: | Jiangsu, China (Mainland) | Standard: | AISI, ASTM, BS, DIN, GB, JIS, Other,JIS,AISI,ASTM,GB,DIN,EN |
---|---|---|---|
Grade: | Nitronic 50 | Type: | Bar |
Dimensions: | 10-900MM | Length: | 2m,3m Or As Required |
Special Use: | Valve Steel | Delivery: | 25-30 Days Subject To The Clients' Requirements And Quantity |
Surface Treatment: | Bright&smooth | Application: | Structural Steel Bar |
High Light: | nitronic 60 stainless steel,nitronic 60 bar,2m Nitronic 50 Round Bar |
High Strength And Good Corrosion Resistant Nitronic 50 Alloy Bar
1 . Description
NITRONIC 50 Stainless Steel provides a combination of corrosion resistance and strength not found in any other commercial material available in its price range. This austenitic stainless has corrosion resistance greater than that provided by Types 316 and 316L, plus approximately twice the yield strength at room temperature. In addition, Armco NITRONIC 50 Stainless has very good mechanical properties at both elevated and sub-zero temperatures. And, unlike many austenitic stainless steels, NITRONIC 50 does not become magnetic when cold worked
2.High Strength (HS) Bar Properties
NITRONIC 50 stainless bars also are available in a high-strength condition attained by special processing techniques. The superior strength of NITRONIC 50 HS produced by hot-rolling is size dependent, approaching that of annealed bars with sizes over 3” diameter. Because its high strength is produced by mill processing, welding operations cannot be performed on this material without loss of strength. Highstrength bars produced by rotary forgingspecial practice may have somewhat reduced resistance to corrosion and sulfide stress cracking.
3 . Chemical Composition:
Grade | % | Ni | Cr | Fe | C | Mn | Si | N | Mo | Nb | V | P | S |
XM-19 | Min | 11.5 | 20.5 | 52 | 4 | 0.2 | 1.5 | 0.1 | 0.1 | ||||
Max | 13.5 | 23.5 | 62 | 0.06 | 6 | 1 | 0.4 | 3 | 0.3 | 0.3 | 0.04 | 0.03 |
4 . Alloy miniumum mechanical properties in the room temperature:
Grade | Tensile Strength (Mpa) | Yield Strength (Mpa) | Elongation (%) | Hardness HB |
XM-19 | 690 | 380 | 35 | ≤241 |
5 . Heavy Section Weld Joint Properties
The mechanical properties of welds in 1-1/4" (32.1 mm) thick plate have been determined using two weld processes that are normally employed in heavy section welding, namely, (a) shielded metal arc (SMA) or stick electrode welding and (b) gas metal arc (GMA) or MIG welding with the spray mode. Heat input is important in obtaining the most satisfactory weld joint. Narrow stringer beads rather that a wide "weave" technique should be used for highest weld ductility. Good shielding of the molten puddle is important to eliminate additional nitrogen from the atmosphere that could cause porosity. Both stringer beads and adequate shielding are normal factors in good stainless steel welding practice.
Contact Person: Kara Liu
Tel: 0086-13914912658
Polished Duplex 2205 Round Bar , S31803 Stainless Steel Round Bar High Alloy Steels
Alloy Duplex 2507 Plate With Superior Chloride Pitting Resistance
S32900 Duplex Stainless Steel Bar / Rod For Desalination Equipment
S32760 Stainless Steel Metal Strips With Erosion Corrosion Resistance
15-5 PH Bar Precipitation Hardening Stainless Steel UNS S15500 Grade For Nuclear Waste Casks
High Toughness 17 4 Steel Plate , 17 4ph Plate For Shaft And Bearing
Low Carbon Content 17 7PH Plate With Superior Weldability 0.282 Lb / Inch3 Density
Stainless Steel Inconel 625 Bar With Stress Corrosion Cracking Resistance
8mm-100mm Thickness Inconel Nickel Alloy Plate , Inconel 718 Plate Mill Edge
Special Metals Inconel 718 Bar , Nickel Alloy 718 With Ending Machinability
Wonderful Machining And Welding Inconel 625 Material Nickel Plate Type